Announcement

Collapse
No announcement yet.

Pro-Flo 4 CAN Bus Data Stream Info

Collapse
This is a sticky topic.
X
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • #46
    I installed the Banks idash1.8. And it is fantastic. Recommend to everyone, easy to install and a quick Amazon search for a solderless db9 and a bit of additional wire and you are done. Mount it how or where you like.
    You do not have permission to view this gallery.
    This gallery has 2 photos.

    Comment


    • #47
      Question: Can the Can have 2 different outputs? be a splitter or something? I have the above idash, and am thinking about the compushift for the 700r4. can this be done?

      Comment


      • #48
        You use a Can bus Y adapter.
        At 43,861 MPH Elon Musk now owns the fastest car in this Galaxy

        Comment


        • #49
          Thanks Bite_me

          Comment


          • #50
            Can a Snap On scanner with Bluetooth recieve data from Pro Flow ECM?

            Comment


            • #51
              No. You have to use the can bus line to receive data from the ECU.
              At 43,861 MPH Elon Musk now owns the fastest car in this Galaxy

              Comment


              • #52
                Originally posted by Monkeysgarage View Post
                I installed the Banks idash1.8. And it is fantastic. Recommend to everyone, easy to install and a quick Amazon search for a solderless db9 and a bit of additional wire and you are done. Mount it how or where you like.
                What is the trick for the i dash to display what it should from the PF4 CAN bus?
                With mine the choices in gauge set up is limited and most don't work, battery voltage works but that's about it.
                I updated firmware and did the set up multiple times.

                Comment


                • #53
                  You got it hooked up with the 4 wires to the canbus?
                  POS
                  Neg
                  Hi can
                  Low can

                  From there just change the gauges displayed through settings on gauge.

                  There is a List of output from ECU to dash on the banks site. There are 10 output for memory. Saves you time trying to figure out what is what.

                  I Have mine set to 8 different displays. They are plenty large enough to view easily.

                  Comment


                  • #54
                    I just hooked up the 2 wires can+ can-
                    white wire and green wire
                    maybe that's the issue

                    thanks
                    I'll check the documents from banks again.

                    Comment


                    • #55
                      i bought a solderless plug and 2 stand of wire (already had a few connecters sitting around) from amazon and ran the + and - and a pos and neg (put it all in a single harness from gauge tail to ecu) and into the bus plug. I have the plug that looks like an old printer plug not the newer one.

                      if you done have a harness to wrap it in, you can make your own.

                      1 grab roll of elec tape.
                      start it and roll it back on itself
                      keep rolling till you have a roll about as thick as your thumb
                      then apply it to the wires
                      this way you get a decent looking result without using a harness, and it is 100% easier than trying to wrap it straight from the roll .

                      Comment


                      • #56
                        My can bus from the edelbrock pf4 has the DB9 connector, I spliced the green and white wires from the I dash right into the edelbrock harness instead of using a DB9 connector.
                        the other 2 wires off the i dash are the ground and power wires.
                        The I dash powers up fine like it should but just doesn't give me the gauge choices that the list says I should have.

                        Comment


                        • #57
                          That wiring shouldnt be a problem at all. But just for testing if easy to do build a db9 connector (amazon somderless is a out 5 bucks) and use the 4 wires from the can to run the gauge.


                          What part number do you have?

                          Banks iDash® 1.8 DataMonsterNo OBD, Primary Gaugefor vehicles without OBD

                          SKU: 66763

                          Or

                          Banks iDash® 1.8 SuperGaugeNo OBD, Primary Gaugefor vehicles without


                          SKU: 66563

                          What options do you get when you try to get to the setting?

                          Comment


                          • #58
                            http://shop-banks.s3.amazonaws.com/p.../Edelbrock.pdf

                            These are the options You should see

                            Comment


                            • #59
                              Page 12 : https://s3.amazonaws.com/assets.bank...ketECU_web.pdf
                              At 43,861 MPH Elon Musk now owns the fastest car in this Galaxy

                              Comment


                              • #60
                                I have the 66763

                                Comment

                                Working...
                                X